研究者詳細 - 大澤　友紀子

論文 - 大澤　友紀子

分割表示 >> ／全件表示 27 件中 1 - 27 件目

Stiffness Control of Thermally Driven Actuator Using Phase Transition

Haruki Saito, Yukiko Osawa

Proceedings of the IEEE World Haptics Conference 2025 （IEEE） 2025年

研究論文（国際会議プロシーディングス）, 最終著者, 責任著者, 査読有り

This paper proposes a method for controlling the stiffness of a thermally driven actuator by leveraging the phase transition of a low-boiling-point liquid. Using a Peltier device for cooling, the reduction in actuator stiffness can be precisely adjusted.
Experiments demonstrated the actuator's effectiveness, particularly in handling fragile objects with precision, ensuring delicate interactions with contact surfaces. Since stiffness is adjusted within a safe temperature range, this approach shows promise for applications involving direct human contact, such as the outer surfaces of social robots (robot skin).

Fluid-Based Contact Detection and Thermal Display

Daisuke Shionoiri, Yukiko Osawa

Proceedings of the JEME 8th International Conference on Advanced Mechatronics （JSME） 2024年11月

研究論文（国際会議プロシーディングス）, 最終著者, 責任著者, 査読有り

Soft robot skin is one of the key factors for physical human-robot interaction (pHRI), and many studies have proposed various kinds of robot skin. In particular, two functionalities, the ability to convey warmth to humans and to detect contact, are significant among the roles of robot skins. The former is known to create comfort and a positive impression of robots and help build trust in them. The latter enables more personalized human support.
However, temperature feedback and contact detection require sensors on the skin's surface; this can disturb the heat conduction from the skin surface and soft, smooth tactile feelings. This paper proposes a system design for fluid-based soft robot skin, simultaneously enabling contact detection and temperature control without attaching a sensor to the skin surface. We developed a skin prototype based on the proposed design and conducted experiments to verify its capabilities.

Robot soft thermal display using self-heating and cooling system

Osawa, Y; Ogura, I; Kheddar, A

CASE STUDIES IN THERMAL ENGINEERING 63 2024年11月

筆頭著者, 責任著者, ISSN 2214-157X

In this paper, we address robotic haptics with the following question: is it possible to design a heating/cooling system that can fulfill both the necessity of keeping the inner robot actuators at a desired optimal heat and, at the same time, use actuators energy loss in terms of heat conveyed, through a soft robotic cover, as pleasant thermal sensation to a human when the robot is touched? We propose a solution to address this question in terms of mechatronic design. Indeed, internal heat generated by actuator loss can be transferred to the robotic haptic cover and a cooling tank for thermal display purposes. A suitable switching control strategy is divided to fulfill the double objective of keeping the actuators’ temperature under a given threshold whilst displaying the desired temperature to the soft robot's cover. We assess our ideas with an experimental set-up using one actuator and our original soft cover technology with a preliminary user study.

Access to Document (DOI)

A Cybernetic Avatar System to Embody Human Telepresence for Connectivity, Exploration, and Skill Transfer

Cisneros-Limón R., Dallard A., Benallegue M., Kaneko K., Kaminaga H., Gergondet P., Tanguy A., Singh R.P., Sun L., Chen Y., Fournier C., Lorthioir G., Tsuru M., Chefchaouni-Moussaoui S., Osawa Y., Caron G., Chappellet K., Morisawa M., Escande A., Ayusawa K., Houhou Y., Kumagai I., Ono M., Shirasaka K., Wada S., Wada H., Kanehiro F., Kheddar A.

International Journal of Social Robotics （International Journal of Social Robotics） 17 （ 3 ） 535 - 562 2024年01月

共著, 筆頭著者, 責任著者, 査読有り, ISSN 1875-4791

This paper describes the cybernetic avatar system developed by Team JANUS for connectivity, exploration, and skill transfer: the core domains targeted by the ANA Avatar XPRIZE competition, for which Team JANUS was a finalist. We used as an avatar a humanoid robot with a human-like appearance and shape that is capable of reproducing facial expressions and walking, and built an avatar control system that allowed the operator to control the avatar through equivalent mechanisms of motion; that is, by replicating the upper-body movement with naturalness and by stepping to command locomotion. In this way, we aimed to achieve high-fidelity telepresence and managed to be well evaluated from the point of view of the operator during the competition. We introduce our solutions to the integration challenges and present experimental results to asses our avatar system, together with current limitations and how we are planning to mitigate them in future work.

Access to Document (DOI)

Integration of Soft Tactile Sensing Skin with Controllable Thermal Display toward Pleasant Human-Robot Interaction

Osawa Y., Luu Q.K., Nguyen L.V., Ho V.A.

2024 IEEE/SICE International Symposium on System Integration, SII 2024 （2024 IEEE/SICE International Symposium on System Integration, SII 2024） 369 - 375 2024年01月

共著, 筆頭著者, 責任著者, 査読有り

Safe and pleasant physical human-robot interaction (pHRI) is essential in the robotic skin and related control paradigms. Among approaches, integrating tactile sensing and thermal techniques enables the robot to provide pleasant and gentle touch perceptions, thus enhancing likability and trustworthiness during interactions with humans. However, achieving both accurate tactile sensing and desired thermal comfort perceptions poses significant challenges. In response to these challenges, this paper presents the development of a novel soft skin named Thermo Tac. This innovative skin not only possesses the ability to sense physical touches effectively but also provides thermal comfort sensations. The integration of these capabilities is realized through a carefully designed and strategic system. The developed skin is integrated with vision-based tactile sensing and water circulation systems to evaluate its performance and effectiveness in realistic interaction scenarios. The results of the experiments highlight the potential of ThermoTac as a promising solution for safe and stable human-robot interaction, paving the way for advanced tactile sensing and thermal comfort in robotics.

Access to Document (DOI)

人とロボットの温熱コミュニケーション

大澤友紀子

日本ロボット学会誌（一般社団法人日本ロボット学会） 42 （ 10 ） 974 - 977 2024年

筆頭著者, 責任著者, ISSN 02891824

Robotic Thermoregulation for Material Identification using Recycled Inner-Generated Motor Heat

Osawa Y., Domae Y., Ogura I., Furukawa Y., Kheddar A.

2023 IEEE International Conference on Robotics and Biomimetics, ROBIO 2023 （2023 IEEE International Conference on Robotics and Biomimetics, ROBIO 2023） 1 - 7 2023年12月

共著, 筆頭著者, 責任著者, 査読有り

The heat generated inside robots originates mainly from energy loss in actuators, onboard electronic circuits, and computation processing units. Typically, it can be dissipated by forced air (most commonly used in robotics) or fluid convection. In this study, we developed a recycled inner-generated heat system inspired by biological thermoregulation mechanism, utilizing the inner heat to the robot's thermal perceptions of a finger-pad (by analogy to human fingertip) for object haptic recognition. Among the fingertips' thermal perceptions, material recognition identifies and distinguishes touched objects, even if the color, stiffness, or roughness are similar. This recognition approach requires a heat source to induce temperature changes at the contact surface to recognize ambient (room) temperature objects. We use an actuator that generates heat in a closed-flow water circuit (by analogy to human cardiovascular system) to induce heat at contact like humans with body temperature and touch. Our thermal method is assessed through experimental simulations of robotic water circulation and a pump system (by analogy to human heart) with the developed finger-pad. The proposed strategy enables it to completely classify three kinds of material covering the same material in 0.7 sec touch.

Access to Document (DOI)

Active Heat Flow Sensing for Robust Material Identification

Osawa Y., Kase K., Furukawa Y., Domae Y.

IEEE Access （IEEE Access） 11 143896 - 143906 2023年12月

共著, 筆頭著者, 責任著者, 査読有り

Thermal properties are significant for recognizing an object's material but cannot be determined via visual and stiffness (or tactile)-based recognition techniques. Most studies have used temperature as a complementary part of multimodal sensing; however, the thermal signal is an unexplored capability that can be beneficial for recognizing target objects. Since changes in thermal responses can result from both material properties and initial temperature, realizing robust and high-accuracy recognition in different environments is a challenging issue. To tackle the issue, this paper proposes a novel strategy for material identification that can actively measure heat flow by heating and cooling a robot gripper, enabling the extraction of the thermal properties of contact materials regardless of the object's initial temperature variation (referred to as 'active heat flow sensing'). We use a robotic task as an example of one possible application of the proposed strategy. For this, we developed a gripper pad embedded in a temperature control system and heat flow sensor to monitor the thermal exchange during contact with a target object. The paper conducted some experiments divided into two scenarios. The first experimental results show that active heat flow sensing is realized within 0.4 sec from first contact for 100% classification of four heated materials. The second experimental results show that the three materials, whose thermal properties are largely different, can be classified within 0.7 sec from first contact using different initial temperatures of the training and test data. These results suggest robustness against environmental change, which has been difficult using conventional temperature-based methods.

ロボットの自己発熱を活用した認識・制御技術の検討―ロボットの血液循環システム実現に向けて―

大澤友紀子, 堂前幸康, 古川慈之

ロボティクス・メカトロニクス講演会講演概要集（一般社団法人日本機械学会） 2023 2A2-C03 2023年

筆頭著者, 責任著者

This study proposes a circulating water system with human blood circulation capacity to utilize the robot’s self-heating effectively. Water channels (robot’s blood vessels) are embedded in the skin covering the robot, controlling and managing the thermal conditions of the robot system. In the process of dissipating the heat generated by the actuator, the heat is transferred to the robot skin in contact with people and objects to enable recognition of the target materials and give a pleasant warmth for human interaction. The proposed method is an innovative way to solve two traditional problems: ”how to avoid overheating of the actuator” and ”how to improve robot skin’s perception ability.”

Access to Document (DOI)

Material Classification Using Active Temperature Controllable Robotic Gripper

Osawa Y., Kase K., Domae Y., Furukawa Y., Kheddar A.

2022 IEEE/SICE International Symposium on System Integration, SII 2022 （2022 IEEE/SICE International Symposium on System Integration, SII 2022） 479 - 484 2022年01月

共著, 筆頭著者, 責任著者, 査読有り, ISSN 23318422

Recognition techniques allow robots to make proper planning and control strategies to manipulate various objects. Object recognition is more reliable when made by combining several percepts, e.g., vision and haptics. One of the distinguishing features of each object's material is its heat properties, and classification can exploit heat transfer, similarly to human thermal sensation. Thermal-based recognition has the advantage of obtaining contact surface information in real-time by simply capturing temperature change using a tiny and cheap sensor. However, heat transfer between a robot surface and a contact object is strongly affected by the initial temperature and environmental conditions. A given object's material cannot be recognized when its temperature is the same as the robotic grippertip. We present a material classification system using active temperature controllable robotic gripper to induce heat flow. Subsequently, our system can recognize materials independently from their ambient temperature. The robotic gripper surface can be regulated to any temperature that differentiates it from the touched object's surface. We conducted some experiments by integrating the temperature control system with the Academic SCARA Robot, classifying them based on a long short-term memory (LSTM) using temperature data obtained from grasping target objects.

Access to Document (DOI)

Soft robotic shell with active thermal display

Osawa Y., Kinbara Y., Kageoka M., Iida K., Kheddar A.

Scientific Reports （Scientific Reports） 11 （ 1 ） 2021年12月

共著, 筆頭著者, 責任著者, 査読有り, ISSN 2045-2322

Almost all robotic systems in use have hard shells, which is limiting in many ways their full potential of physical interaction with humans or their surrounding environment. Robots with soft-shell covers offer an alternative morphology which is more pleasant in both appearance and for haptic human interaction. A persisting challenge in such soft-shell robotic covers is the simultaneous realization of softness and heat-conducting properties. Such heat-conducting properties are important for enabling temperature-control of robotic covers in the range that is comfortable for human touch. The presented soft-shell robotic cover is composed of a linked two-layer structure: (1) The inner layer, with built-in pipes for water circulation, is soft and acts as a thermal-isolation layer between the cover and the robot structure, whereas (2) the outer layer, which can be patterned with a given desired texture and color, allows heat transfer from the circulating water of the inner part to the surface. Moreover, we demonstrate the ability to integrate our prototype cover with a humanoid robot equipped with capacitance sensors. This fabrication technique enables robotic cover possibilities, including tunable color, surface texture, and size, that are likely to have applications in a variety of robotic systems.

Access to Document (DOI)

A Soft Robotic Cover with Dual Thermal Display and Sensing Capabilities

Osawa Y., Kheddar A.

Springer Proceedings in Advanced Robotics （Springer Proceedings in Advanced Robotics） 19 253 - 262 2021年10月

共著, 筆頭著者, 責任著者, 査読有り, ISSN 2511-1264

We propose a new robotic cover prototype that achieves thermal display while also being soft. We focus on the thermal cue because previous human studies have identified it as part of the touch pleasantness. The robotic cover surface can be regulated to the desired temperature by circulating water through a thermally conductive pipe embedded in the cover, of which temperature is controlled. Besides, an observer for estimating heat from human contact is implemented; it can detect human interaction while displaying the desired temperature without temperature sensing on the surface directly. We assessed the validity of the prototype in experiments of temperature control and contact detection by human hand.

Access to Document (DOI)

Thermal Rendering Based on Thermal Diffusion Equation

Yukiko Osawa, Seiichiro Katsura

IEEJ JOURNAL OF INDUSTRY APPLICATIONS （INST ELECTRICAL ENGINEERS JAPAN） 8 （ 6 ） 867 - 874 2019年11月

共著, 筆頭著者, 責任著者, 査読有り, ISSN 2187-1094

Actuator arrays that consist of a planar arrangement of actuators are widely used for transportation of objects or shaping a rough surface by controlling the actuators cooperatively. In particular, thermal displays that consist of multiple heat sources spread over a surface have been developed for many years. Generally, the expression ability is determined by the number of actuators in actuator arrays, and accordingly, thermal displays require many heat sources to ensure a high spatial resolution of temperature distribution. However, the number of usable heat sources is limited because of mechanical issues. In order to solve this problem, a control method that employs a model derived from a thermal diffusion equation and is used between two heat sources, is proposed in this paper. By using the proposed method, any selected point of the heat conduction can be expressed using only one heat source. Therefore, infinite number of nodes of propagation can be reproduced by selecting a desired node. The method is expected to extend the technology for controlling multiple actuators or heat sources on a surface.

Access to Document (DOI)

Variable Heat Disturbance Observer for Control of Peltier Device

IEEJ JOURNAL OF INDUSTRY APPLICATIONS （INST ELECTRICAL ENGINEERS JAPAN） 8 （ 2 ） 185 - 191 2019年03月

共著, 筆頭著者, 責任著者, 査読有り, ISSN 2187-1094

A thermoelectric device called a Peltier device is widely used in many fields. For example, the device is used for a cooling system such as in systems consisting of medical reagent coolants and refrigerators. However, controlling the device is difficult because thermal characteristics of the device change depending on its temperature. Notably, the amount of heat flow generated from the device varies with the amount of current applied. Therefore, a thermal nonlinear behavior has to be considered in a thermal model. Most studies do not consider the nonlinear characteristics and treat the device as a linear system. Therefore, robustness against disturbance is not high because of modeling error. This paper presents a heat disturbance observer considering the nonlinear characteristics of a Peltier device. Variable parameters depending on the temperature and current of the device are used, and a variable heat disturbance observer is proposed. The thermal model used in the proposed observer includes a few nonlinear elements such as Joule heat and heat flow inside the device. The objective of this study is to improve the response of a Peltier device. Some experiments were conducted to verify the validity of the proposed method. Besides, the effect of modeling error on the stability of the observer is discussed.

Access to Document (DOI)

Rendering Thermal Sensation of Fingertip by Using Spatial Information of Heat Sources

Yukiko Osawa, Seiichiro Katsura

2019 IEEE/SICE INTERNATIONAL SYMPOSIUM ON SYSTEM INTEGRATION (SII) （IEEE） 620 - 625 2019年01月

筆頭著者, 責任著者, 査読有り, ISSN 2474-2317

To encourage interaction between a human and a robot, a technique of giving a thermal sensation is needed. In particular, the technique is important for the case of offering a sense of security such as nursing care robot and rehabilitation robot. Thermal sensation is perceived from the temporal and spatial information of heat sources. Therefore, the model included such information is needed to control multiple heat sources as a single system. In this paper, the fingerstall attached four heat sources was developed and its control method for rendering spatial thermal sensation is proposed. The four heat sources are attached to the copper plate, and the human finger is thermally stimulated by touching the plate. The temperature distribution on the copper plate is modeled based on a two-dimensional thermal diffusion equation, and spatial thermal sensation can be rendered using the proposed system. Some experiments were conducted to verify the proposed thermal system and its control system.

Thermal Propagation Control Using a Thermal Diffusion Equation

Yukiko Osawa, Seiichiro Katsura

IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS （IEEE-INST ELECTRICAL ELECTRONICS ENGINEERS INC） 65 （ 11 ） 8809 - 8817 2018年11月

筆頭著者, 責任著者, 査読有り, ISSN 0278-0046

Controlling heat flow is necessary in many fields, such as the communications, health care, and manufacturing industries. In the communication field, the techniques for the reproduction of thermal sensations have been researched for many years. In order to extend the area of controlling the heat, the thermal diffusion in time and space needs to be considered. However, attaining precise control based on conventional methods is difficult because it requires several sensors and devices to monitor and control the temperature distribution. In this study, the thermal system consists of a metal wire and a Peltier device attached to the end of the wire, and a one-dimensional thermal propagation system is constructed. Modeling the thermal diffusion equation, it was found that the thermal system has characteristics of damping and propagation delay. Therefore, a control method using these system characteristics is proposed. The thermal system is treated as a time delay system with damping, which is compensated by a time delay and damping compensator. The thermal diffusion through the system can be considered by the proposed method. Experimental results show the viability of the proposed control system.

Access to Document (DOI)

Wearable Thermal Interface for Sharing Palm Heat Conduction

Yukiko Osawa, Seiichiro Katsura

IECON 2018 - 44TH ANNUAL CONFERENCE OF THE IEEE INDUSTRIAL ELECTRONICS SOCIETY （IEEE） 3310 - 3315 2018年10月

共著, 筆頭著者, 責任著者, 査読有り, ISSN 1553-572X

Developing a thermal interface to share a thermal sensation between remote locations can lead to significant progress in the field of haptics. The research focuses on a technique of rendering thermal sensation that is an essential element of the haptics for touching human and machines each other. The thermal technique is required in case of offering a sense of security and sharing a precise hand with thermal sensations between remote places such as nursing care and rehabilitation robot. This paper proposed a method to control heat conduction on a palm by setting virtual thermal conductance between two fingers of the glove. Two thermal gloves are used as a master/slave systems, and the virtual thermal conductance can change heat conduction on the palm. The proposed interface and its control algorithm can be used to share a spatial thermal sensation on a palm. The experimental results indicate the validity of the proposed method. The interface and its control system are expected to connect people in remote locations, and the developed system can potentially be used in medical and multimedia applications.

Simultaneous Presentation of Thermal and Tactile Sensations Using Multilateral Control under Time Delay

Satoshi Nishimura, Yukiko Osawa, Hiroki Kurumatani, Yuki Nagatsu, Kazumasa Miura, Seiichiro Katsura

IEEJ JOURNAL OF INDUSTRY APPLICATIONS （INST ELECTRICAL ENGINEERS JAPAN） 7 （ 5 ） 378 - 386 2018年09月

共著, 筆頭著者, 責任著者, 査読有り, ISSN 2187-1094

This paper presents a method of simultaneously presenting tactile and thermal sensations using multilateral tele-operation. Communication using haptic sensation is expected to be a next-generation communication tool replacing telephone or television. A control technique named multilateral control can transmit haptic sensation to multiple points. In this study, robot manipulators are used for tactile sensation presentation, and Peltier devices are used for rendering thermal sensation. A position encoder is used to measure the position of a robot and also estimate the external force, while temperature and heat flow sensors are used for rendering thermal sensation. A routing method to decouple controllers compensates the effect of a time delay between the systems. Defining a modal transformation matrix in a network system eliminates the interference effect of controllers, which is a well-known problem in bilateral and multilateral teleoperation. The matrix shows how to route the information to realize mode-decoupled control in network systems. To consider the motion range of a robot manipulator, the scaling gain is inserted into the modal transformation matrix. The method also compensates the difference between the response speeds of robot manipulators and Peltier devices. This should be considered because the response speed of a Peltier device is slow compared to that of a robot manipulator. The validity of the proposed method is confirmed through experiments.

Access to Document (DOI)

Distributed Thermal Conductance Control for Sensing and Rendering Thermal Sensation on the Palm

Yukiko Osawa, Seiichiro Katsura

2018 IEEE 15TH INTERNATIONAL WORKSHOP ON ADVANCED MOTION CONTROL (AMC) （IEEE） 328 - 333 2018年03月

共著, 筆頭著者, 責任著者, 査読有り, ISSN 1943-6572

Sensing and rendering thermal sensation is important to the multimedia, communication, and medical field. For example, human health care system for monitoring and treating a body temperature distribution can be estimated by using the technique. In this research, the thermal interface using multiple heat sources for rendering thermal sensation is treated. In order to control a lot of heat sources in the thermal interface, the distributed control method is required to render spatial continuous sensation. The paper defined "Distributed thermal conductance" that the relationship between heat sources, and heat flow on the palm can be freely changed depending on the connectivity between heat sources. The proposed method can be controlled the desired temperature distribution on the surface of the interface.

Sensing of Heat Source in a Deep Layer by Considering Heat Propagation

Yukiko Osawa, Seiichiro Katsura

IEEJ JOURNAL OF INDUSTRY APPLICATIONS （INST ELECTRICAL ENGINEERS JAPAN） 7 （ 3 ） 229 - 235 2018年03月

共著, 筆頭著者, 責任著者, 査読有り, ISSN 2187-1094

Human sensing and tactile transmission utilizing thermal interface are necessary to support human life or for communicating with people in remote locations. For instance, the devices are used for remote health care, telesurgery, and so on. Many studies have utilized a Peltier device as the thermal interface, and there are many studies on the control and sensing of the device. However, in most of those studies, the heat propagation in the system is not considered, and only the point that is attached to the sensor can be observed and controlled. In particular, this is a problem for health care systems, because it is difficult to obtain information about the inside of the human body where it is hard to attach the sensor. In order to solve this problem, this study considers the heat propagation of materials such as the human body by developing a model based on the thermal diffusion equation. In the case of cooling material, heat propagation changes depending on the material condition, for example, the presence of heat source such as a cancer cell. Based on the thermal characteristics, a method to obtain the heat flow of material using heat propagation is proposed in this paper. It is possible to find a heat source in deep layers of a material by using the proposed method without attaching any sensor inside the material. Some experiments are conducted using aluminum cylinder as a propagation material to verify the validity of the proposed method.

Access to Document (DOI)

Sensing of Heat Source in Deep Layer Using Heat Flow

Yukiko Osawa, Seiichiro Katsura

2017 56TH ANNUAL CONFERENCE OF THE SOCIETY OF INSTRUMENT AND CONTROL ENGINEERS OF JAPAN (SICE) （IEEE） 416 - 419 2017年09月

共著, 筆頭著者, 責任著者, 査読有り

Heat sensing is necessary for human health care and industrial fields. In many cases, the abnormality of human body or machine is appeared as a heat source. For example, a cancer cell is higher temperature by up to 2 or 3 degree on the skin surface over the tumor. Therefore, abnormal detection is possible to sense through the heat distribution in the material. There are many sensors for observing temperature such as thermocouple, thermistor, thermography, and so on. However, sensing in deep layer of material using these sensors are difficult. This paper proposed the sensing method for detecting heat source inside the material by using heat flow. The method uses an algorithm that heat flow is changed depending on temperature difference. Some experiments are conducted to verify the proposed method.

Temperature Control on a Curved Surface for Implementing to Wearable Interfaces

Yukiko Osawa, Seiichiro Katsura

PROCEEDINGS OF THE IECON 2016 - 42ND ANNUAL CONFERENCE OF THE IEEE INDUSTRIAL ELECTRONICS SOCIETY （IEEE） 348 - 353 2016年10月

共著, 筆頭著者, 責任著者, 査読有り, ISSN 1553-572X

Recently, tactile transmission utilizing wearable devices are necessary to support human life or communicating with people in remote locations. One key factor of transmitting tactile sensation is thermal sensation. Flexible thermal devices have been developed, however, precise temperature distribution cannot be reproduced due to the large size and the flexibility of the devices. Therefore, a technique of rendering thermal sensation considering heat propagation is required to obtain the desired temperature distribution. In this paper, a method to control temperature on a curved surface for implementing to wearable devices is proposed. This method can be applied to various shapes of devices because the deformation of a device can be observed by the propagation delay of the heat flow. Experiments are conducted to verify the validity of the proposed method.

Improvements in the safety and efficiency of air traffic

Katsura, S, Osawa, Y, Murata, H

Journal of the Institute of Electrical Engineers of Japan 136 （ 7 ） 2016年07月

共著, 筆頭著者, 責任著者, ISSN 1881-4190

Access to Document (DOI)

Temperature Control for Thermal Sensation Based on Thermal Diffusion Equation

Yukiko Osawa, Seiichiro Katsura

PROCEEDINGS 2016 IEEE 25TH INTERNATIONAL SYMPOSIUM ON INDUSTRIAL ELECTRONICS (ISIE) （IEEE） 1264 - 1269 2016年06月

共著, 筆頭著者, 責任著者, 査読有り, ISSN 2163-5137

Technique of rendering thermal sensation can connect people who are in remote locations, such as teletherapy and a multimodal system. Humans feel detailed temperature distribution and recognize the characteristic of a contacting object. Although, conventional method can only render the thermal sensation of a fingertip or a part of a hand. In the case of combining these techniques with robot for human support, the robot can only touch one point of a material. This paper proposed the method of temperature control for rendering thermal sensation considering spatial diffusion. The method can spread the area of rendering and help rendering spatial sensations. The validity of the proposed method is verified through some experiments.

Control of Thermal Conductance with Detection of Single Contacting Part for Rendering Thermal Sensation

Yukiko Osawa, Hidetaka Morimitsu, Seiichiro Katsura

IEEJ JOURNAL OF INDUSTRY APPLICATIONS （INST ELECTRICAL ENGINEERS JAPAN） 5 （ 2 ） 101 - 107 2016年03月

共著, 筆頭著者, 責任著者, 査読有り, ISSN 2187-1094

The rendering of tactile sensations has recently been attracting attention in the fields of multimedia and communication. This study focuses on thermal sensation, which is one of the important elements for rendering a tactile sensation. Humans feel an object by hand movements such as tracing, grasping, and stroking. In response to such movements, it is necessary to take into account the change in the contacting point on the system. However, most conventional studies on thermal rendering did not take such situations into account in their system design. This study aims to fill this gap by proposing a control method for reproducing thermal conductance with the detection of a single contacting part. In this study, a copper plate attached to a Peltier device is regarded as a thermal system, and the system is modeled with three parts. Heat disturbance observers and heat inflow observers are then allocated to each part, and the thermal conductance at any single part is virtually reproduced. Moreover, a detection method of single contacting part is introduced in the proposed system. Combining the detection method with the controller enables different thermal sensations to be rendered depending on the contacting part.

Access to Document (DOI)

Multiple Temperature Control with Detection of Contacting Points for Rendering Thermal Sensation

Yukiko Osawa, Seiichiro Katsura

IECON 2015 - 41ST ANNUAL CONFERENCE OF THE IEEE INDUSTRIAL ELECTRONICS SOCIETY （IEEE） 4748 - 4753 2015年11月

共著, 筆頭著者, 責任著者, 査読有り, ISSN 1553-572X

Thermal sensation is important for communication tool and multimedia fields as an element of tactile sensation. This research focuses on thermal sensation, and aims to render the sensation spatially. Most of conventional studies present thermal sensation by directly contacting thermal device such as a Peltier device. In this case, it is difficult to get thermal information by the movements of their hands such as tracing. In this paper, a control method for rendering thermal sensation with the consecutive detection of contacting points is proposed. In order to consider temperature distribution of the system, a copper plate attached to the Peltier devices is regarded as a thermal system. A method to detect multiple contacting points is proposed, which uses the value of heat inflow estimated from heat inflow observer, and temperature control at the detected points is conducted. This method enables the system to render spatial thermal sensation in response to the movements of finger. Experimental results show the viability of the proposed control system.

Thermal Impedance Control for Thermal Rendering Technique

Yukiko Osawa, Seiichiro Katsura

IECON 2015 - 41ST ANNUAL CONFERENCE OF THE IEEE INDUSTRIAL ELECTRONICS SOCIETY （IEEE） 4015 - 4020 2015年11月

共著, 筆頭著者, 責任著者, 査読有り, ISSN 1553-572X

Rendering technique of tactile sensation is necessary to communicate and share feelings between remote locations. This research focuses on thermal sensation, and not only precise rendering of tactile information but also environmental identification is conducted. Thermal sensation is changed depending on thermal impedance such as thermal resistance and thermal capacitance. In this paper, the identification method of thermal impedance is proposed, and rendering the identified thermal parameters is conducted. The method consists of identification using thermal conductivity and reproduction based on thermal impedance control. In order to identify thermal parameters of an object, an iterative least square technique is used. The proposed method is able to render thermal response precisely for human because thermal impedance is identified based on heat flow in the same way as human skin sensation. The validity of the proposed method is verified through some experiments.

　前のページ - 次のページ　

大澤 友紀子

論文 - 大澤 友紀子

大澤　友紀子

論文 - 大澤　友紀子